ASTM-B864 2008(Redline)

$26.65

B864/B864M-08 Standard Specification for Corrugated Aluminum Box Culverts (Redline)

Published By	Publication Date	Number of Pages
ASTM	2008	9

Guaranteed Safe Checkout

Categories: 13.060.30 - Sewage water, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

Abstract

This specification covers the requirements for material, geometric, and wall section properties of aluminum box culverts manufactured from corrugated plate or sheet with attached rib stiffeners, for field assembly. Suitable fasteners and optional materials such as aluminum invert plates and headwalls are also described here. Material applications include surface water gravity flow drainage conduits like culverts and storm drains, small bridge, and grade separation structure conduits like pedestrian or vehicular underpasses, and utility tunnels. This specification does not cover the requirements for foundations, backfill, the relationship between earth cover or live loads and strength requirements, or the hydraulic design of these structures. The required plastic moment capacities should be determined for both the crown and haunch segments of the box culverts.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers material, geometric, and wall section properties of aluminum box culverts manufactured from corrugated plate or sheet, with attached rib stiffeners, for field assembly. Appropriate fasteners and optional materials, such as aluminum invert plates and headwalls, are also described. Applications for aluminum box culverts include conduits for gravity flow drainage of surface water, such as culverts and storm drains, as well as for small bridges and grade separation structures such as pedestrian or vehicular underpasses, and utility tunnels.

1.2 This specification does not include requirements for foundations, backfill, or the relationship between earth cover or live loads and strength requirements. These important design considerations are described in the AASHTO Standard Specifications for Highway Bridges and the AASHTO LRFD Bridge Design Specifications.

1.3 This specification does not include requirements for the hydraulic design of these structures. Hydraulic design, placement of footings or inverts, and end treatments to resist scour are described in FHWA HDS No. 5.

1.4 Appendix X1 lists nominal dimensions of box culvert sizes commonly available. Also listed are cross-sectional area and hydraulic design parameters for these sizes.

1.5 Appendix X2 lists manufacturer’s suggested design properties for the rib stiffener types, spacing classes, and material thicknesses described in this specification.

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

ASTM Standards

A36/A36M Specification for Carbon Structural Steel A123/A123M Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products A153/A153M Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware A307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength A563 Specification for Carbon and Alloy Steel Nuts A563M Specification for Carbon and Alloy Steel Nuts (Metric) B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes B746/B746M Specification for Corrugated Aluminum Alloy Structural Plate for Field-Bolted Pipe, Pipe-Arches, and Arches B790/B790M Practice for Structural Design of Corrugated Aluminum Pipe, Pipe-Arches, and Arches for Culverts, Storm Sewers, and Other Buried Conduits

AASHTO Standard

LRFDBridgeDesignSpec

FHWA Standard

HDSNo.5, Hydraulic Design of Highway Culverts, Report No. FHWA-NHI-010-020, Sept. 2001 (Revised May 2005) Available from National Technical Information Service (NTIS), 5285 Port Royal Rd., Springfield, VA 22161, http://www.ntis.gov.

Keywords

bridge; box culvert; corrugated aluminum structural plate; culvert; grade separation; low cover structure; low profile structure; storm sewer; Aluminum box culverts; Box culverts; Corrugated aluminum; Culverts–specifications; Grade separation; Low cover/profile structure; Storm sewer/drainage pipe (Al/Al alloy) ;

ICS Code

ICS Number Code 13.060.30 (Sewage water)

DOI: 10.1520/B0864_B0864M-08 ASTM International is a member of CrossRef.

ASTM B864 / B864M (Nonferrous Metal Standards and Nonferrous Alloy Standards)

Additional information

Standard Title	B864/B864M-08 Standard Specification for Corrugated Aluminum Box Culverts (Redline)
Published Code	ASTM
Publication Date	2008
Pages Count	9
ICS Codes	13.060.30 - Sewage water

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-B864 2008(Redline)

ASTM B864 / B864M (Nonferrous Metal Standards and Nonferrous Alloy Standards)

Related products