This European Standard specifies the requirements for expanded polystyrene (EPS) beads and the adhesive, which are after installation used for the thermal insulation of buildings. The EPS beads and the adhesive are mixed and processed on site. This standard does not specify the required level of a given property to be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application are to be found in regulations or non-conflicting standards. This standard does not cover factory made insulation products in the form of prefabricated shapes or boards made of bonded EPS beads. Products with a declared thermal resistance lower than 0,25 (m\u00b2 x K)\/W or a declared thermal conductivity at 10 \u00b0C greater than 0,1 W\/(m x K) are not covered by this standard.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 7<\/td>\n | 1 Scope 2 Normative references 3 Terms, definitions, symbols and abbreviations 3.1 Terms and definitions <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | 3.2 Symbols and abbreviations 4 Requirements 4.1 General 4.2 Suitability of the building for the installation of the product 4.3 In situ measurements and calculations 4.3.1 General <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | 4.3.2 The installed thermal resistance of masonry cavity wall and frame construction insulation 5 Installation checks 5.1 Average cavity width 5.2 Machine output 5.3 Installed volume 5.4 Thermal resistance of installed masonry cavity wall and frame construction installation <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 6 Guidelines for installation 7 Installer’s declaration <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | Annex\u00a0A (normative)Masonry cavity walls \u2013 Determination of average cavity width A.1 Procedure A.2 Calculation <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | Annex\u00a0B (normative)Masonry cavity walls and frame constructions \u2013 Flow check procedures B.1 Apparatus B.2 Procedure <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | Annex\u00a0C (normative)Masonry cavity walls \u2013 Use of endoscope to check adequacy of fill C.1 Selection of inspection positions by the inspector C.2 Action to be taken by the inspector <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | Annex\u00a0D (normative)Guidance for the installer \u2212 Suitability of the building, training, pre-checks and installation declaration D.1 Masonry cavity walls D.1.1 Suitability of the building to receive the insulation D.1.2 Suitability of the building to receive the insulation <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | D.1.3 Installation procedure D.2 Frame constructions (new build walls) D.2.1 Suitability of the building to receive the insulation <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | D.2.2 Control tests made by the installer when preparing the product on site D.2.3 Installation procedure D.2.4 An example of a declaration form for use by the installer <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Thermal insulation products of buildings. In-situ formed products from loose-fill expanded polystyrene (EPS) beads and bonded expanded polystyrene beads – Specification for the bonded and loose-fill products after installation<\/b><\/p>\n |