{"id":72938,"date":"2024-10-17T16:26:04","date_gmt":"2024-10-17T16:26:04","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/awwa-c903-2005\/"},"modified":"2024-10-24T19:08:33","modified_gmt":"2024-10-24T19:08:33","slug":"awwa-c903-2005","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/awwa\/awwa-c903-2005\/","title":{"rendered":"AWWA C903 2005"},"content":{"rendered":"
This standard describes coextruded polyethylene (PE) composite pressure pipes with a welded aluminum tube reinforcement between the inner and outer layers of polyethylene, primarily for use as underground water service lines.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | ANSI\/AWWA C903-05 <\/td>\n<\/tr>\n | ||||||
3<\/td>\n | Committee Personnel <\/td>\n<\/tr>\n | ||||||
5<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | Foreword I. Introduction. <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | II. Special Issues. <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | Table F.1 Calculated surge pressures for an instantaneous change in velocity of \n1 ft\/sec (0.3048 m\/sec) in PE\u2013AL\u2013PE or PEX\u2013AL\u2013PEX pipe <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | Table F.2 Minimum bending radius for PE\u2013AL\u2013PE and PEX\u2013AL\u2013PEX pipe <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | III. Use of This Standard. <\/td>\n<\/tr>\n | ||||||
15<\/td>\n | IV. Major Revisions. V. Comments. <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | AWWA Standard Polyethylene\u2013Aluminum\u2013Polyethylene and \nCross-linked Polyethylene\u2013Aluminum\u2013 \nCross-linked Polyethylene Composite Pressure \nPipes \n SECTION 1: GENERAL Sec. 1.1 Scope <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | Sec. 1.2 Purpose Sec. 1.3 Application SECTION 2: REFERENCES <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | SECTION 3: DEFINITIONS <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | SECTION 4: REQUIREMENTS Sec. 4.1 Permeation <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | Sec. 4.2 Basic Materials Table 1 PE materials\u2014inner and outer layers* Table 2 Melt adhesive* <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | Table 3 Outside diameters, aluminum thickness, and tolerances Sec. 4.3 Pipe Requirements <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | Table 4 Pipe wall thickness <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | Table 5 Minimum burst pressure and sustained pressure for PE\u2013AL\u2013PE pipe Table 6 Minimum burst pressure and sustained pressure for PEX\u2013AL\u2013PEX pipe <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | Table 7 Pressure design basis (PDB) and pressure rating (PR) Sec. 4.4 Pressure Rating (PR) of Pipe SECTION 5: VERIFICATION Sec. 5.1 General <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | Sec. 5.2 Tests for Qualification of Materials and Processes Sec. 5.3 Tests for Product Quality Control Sec. 5.4 Action After Failure to Meet Requirements Sec. 5.5 Quality Control Records <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | Sec. 5.6 Plant Inspection by the Purchaser SECTION 6: DELIVERY Sec. 6.1 Marking <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | Sec. 6.2 Shipping and Delivery Sec. 6.3 Affidavit of Compliance <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" AWWA C903-05: Polyethylene-Aluminum-Polyethylene Crosslinked Polyethylene Composite Pressure Pipes 1\/2″ (12 MM) Through 2″ (50 MM) For Water Service<\/b><\/p>\n |